快速卷簾門的傳動機構裝置在：門洞的頂盒內。箱體選用22 mm厚鍍鋅鋼板和6 mm厚鋼板，端板上配有卷筒軸承、驅動電機、裝置座和平衡體系部件的裝置孔，鋼板表面涂有客戶要求的色彩。

The transmission mechanism of the fast rolling shutter door is located inside the top box of the door opening. The box is made of 22mm thick galvanized steel plate and 6mm thick steel plate. The end plate is equipped with device holes for drum bearings, drive motors, device seats, and balance system components. The surface of the steel plate is coated with the color required by the customer.

卷軸裝置在機柜內，由卷軸、軸端、軸承座等組成。依據門口的高度和寬度計算出鼓的尺度，挑選合理的尺度。在這個快速卷簾門上，滾筒的直徑是219毫米。

The scroll device is located inside the cabinet and consists of a scroll, shaft end, bearing seat, etc. Calculate the scale of the drum based on the height and width of the doorway, and select a reasonable scale. On this fast rolling shutter door, the diameter of the drum is 219 millimeters.

門簾布：門簾布是分段制作的，每段高度約為兩邊700mm。每段窗簾布經過特制的鋁抗風條連接成一個整體的窗簾布，窗簾布的厚度為1。 2mm，具有強度高、耐沖擊、不易刺穿的優點。也能夠挑選=2mm的通明PVC原料的窗簾布或許組件為通明PVC原料，觀察快速卷簾門兩邊的狀況。簾布底部設有鋁底梁，防撞軟袋簾布頂部用螺絲和壓條固定在卷筒上。

Door curtain fabric: The door curtain fabric is made in sections, with each section height of approximately 700mm on both sides. Each section of the curtain fabric is connected into a single unit by a specially designed aluminum wind resistant strip, with a thickness of 1. 2mm, with the advantages of high strength, impact resistance, and not easy to puncture. It is also possible to select curtain fabrics made of 2mm transparent PVC material or components made of transparent PVC material, and observe the condition on both sides of the quick rolling shutter door. The bottom of the curtain is equipped with an aluminum bottom beam, and the top of the anti-collision soft bag curtain is fixed to the drum with screws and pressure strips.

驅動設備：快速卷簾門的轉軸由減速電機直接驅動。依據升降速度的要求，挑選不同速比的減速機達到所需的升降速度，Z向速度可達80 cm/s以上，操控線選用變頻操控，使簾布在運轉中緩慢啟停，簾布在運轉中停止移動。

Driving equipment: The shaft of the fast rolling shutter door is directly driven by a deceleration motor. According to the requirements of lifting speed, select reducers with different speed ratios to achieve the required lifting speed. The Z-direction speed can reach 80 cm/s or above. The control line adopts variable frequency control to slowly start and stop the fabric during operation, and the fabric stops moving during operation.

導槽箱：導槽箱2厚2厚mm鍍鋅鋼板制成，固定在門洞兩邊的墻上，機箱放置在導槽箱頂部，經過螺栓固定在導槽箱和墻上。導槽箱的導槽兩邊固定有密封條，以證一定的密封要求，導槽箱底部離地約1m假如位置較高，則保留紅外監視器的裝置位置。

Guide box: The guide box is made of 2mm thick galvanized steel plate and fixed on the walls on both sides of the door opening. The chassis is placed on the top of the guide box and fixed to the guide box and wall with bolts. There are sealing strips fixed on both sides of the guide groove of the guide groove box to meet certain sealing requirements. If the bottom of the guide groove box is about 1m above the ground, the position of the infrared monitor device should be retained.